Print this page
NV-202G
2 Giga LAN Over VDSL2 Extender with DIP Switch
Ordering Information | ||
NV-202G | 2 Giga LAN Over VDSL2 Extender with DIP Switch |
- OVERVIEW
- FEATURES
- SPECIFICATIONS
- APPLICATIONS
- DOWNLOAD
Product OVERVIEW
NV-202G is an end to end solution using the G.993.2 VDSL2 standard technology and providing up to 160Mbps symmetric using only a single copper wire pair. Designed specifically or a LAN to LAN extension and supporting both symmetrical and asymmetrical transmission at up to 160/160Mbps within 300 meters and 5/1Mbps at 3000 meters, this is a perfect solution to extend LAN to buildings, hotels, hospitals or any location outside of the 100 meters reach of Ethernet UTP.
- Flexible Configuration
- G.INP / G998.4
- Easy Installation
- Automatic Bandwidth detection
The NV-202G supports both central office (CO) and customer-premises equipment (CPE) modes selectable through DIP Switch. Customers can do the configuration for different needs adjustment. PIN1 ON of DIP Switch is CPE side, PIN1 OFF of DIP Switch is CO side.

G.998.4 is a newer alternative to FEC (Forward Error Correction) and interleaving to providing a lower overhead (FEC loses about 12% whereas G.INP only corrects errors when they actually occur) so there is little overhead. G.998.4 was formerly known as G.INP and may also be referred to as Impulse Noise Protection or Physical Retransmission (PHY-R).
G998.4 operates at the physical layer. The transmitting modem keeps a copy of transmitted data in a retransmission buffer. If the receiver detects corruption (by way of a checksum) a retransmission is requested. If the transmitter responds in time, the data is repaired. The round-tip time of a retransmission should be <4ms. If the transmitter doesn't retransmit in time, the corrupt data is forwarded for higher level protocols to sort out.
The NV-202G may be installed on any level surface (e.g. a table or shelf or rail) that use bracket or DIN rail plate. The NV-202G supports plug-and-play installation and is fully compatible with all kinds of network protocols. Furthermore, user can watch the status of each individual port via the LED indicators.
The NV-202G supports band profile 17a and 30a, it can automatically detect the cable length and bandwidth depending on the distance to the configuration.
FEATURES
- Supports VLAN tag pass-through
- Supports G.INP(G.998.4)
- Supports vectoring function(NV-202T only for Telecom requirements)
- Supports UPBO and DPBO
- Support 2 x Giga ethernet ports
- Supports RJ-11/Terminal Block combo for Line port
- Supports high bandwidth up to 160Mbps symmetric over Line ports
- Supports long reach mode up to 3 km with 24 AWG phone wire
- Supports auto speed for Line port and Interleave mode selectable through CO side DIP switch
- DIP switch with Master (CO) and Slave (CPE) mode selectable
- Support 8 bands selectable and INP
- Supports long packet size up to 2000 bytes
- Built-in Lightning Surge protector
- Compact size and Metal case design for flexible installation
- Supports wall mounting installation
- Supports DIN-Rail mount installation (Optional)
- Supports point-to-point applications
* Specifications are subject to change without prior notice.
Specifications
Standard Conformance | ||
Standard: | IEEE802.3 / IEEE802.3u / IEEE802.3ab standard ITU-T G993.2 VDSL2 standard |
|
Regulatory Compliance: | FCC CE |
|
Hardware Specifications | ||
Physical Interface: | 2 x RJ-45 10/100/1000Mbps auto-negotiation / auto-MDIX Ethernet port 1 x RJ-11/Terminal Block combo for line port 1 x DIP Switch 1 x Power Jack |
|
Cable Connections: | RJ-45 (Ethernet): Category 3~7 UTP/STP RJ-11 (Line): Twisted Pair phone wire |
|
LED indication: | 1 x Power LED 2 x Link/Active indicator for Ethernet port 1 x Link/Active indicator for Line port 1 x CO Mode indicator LED 1 x CPE Mode indicator LED |
|
Power Requirement: | Input Voltage: 12VDC / 1A (Commercial-grade Power Adapter) | |
Typical Power Consumption: | 5W | |
VDSL2 Line Code: | Discrete multitone (DMT) modulation | |
VDSL2 Transmission Mode: | Packet Transfer Mode (PTM) | |
Operating Temperature: | 0°C~ 50°C (32°F ~ 122°F) Fanless, free air cooling | |
Storage Temperature: | -20°C ~ 70°C (-4°F ~ 158°F) | |
Humidity: | 10 to 90% (non-condensing) | |
Weight: | 0.34 kg | |
Dimensions: | 95 x 110 x 27 mm (3.74" x 4.33" x 1.06") | |
* Specifications are subject to change without prior notice.
APPLICATIONS
LAN Distance Extension
Two NV-202G acting as a standalone pair is good for Ethernet distance extension over existing telephone wires. With just one pair of AWG-24 copper wire, you can easily connect the maximum data rate of 100Mbps and up to 3km distance support. It is easy-to-use which do not requires installation of additional wiring. Every modular phone jack in the home can become a port on the LAN.
