Home » Products » NV-450

G.fast Master modem + G.fast / VDSL2/V35b Slave Modem
 Ordering Information
NV-450M/S
G.fast Master Modem + G.fast / VDSL2 / V35b   Slave Modem ( Please contact us for actual leadtime. )

 

 

  • Overview
  • Features
  • Specifications
  • Applications
  • Download
  • FAQ

 

NV-450M/S is a managed G.fast point to point solution with four Gigabit LAN ports. It is compliant to ITU-T
G.9700/9701 Standards and supports G.fast 106/212 dual wave profile, bandwidth is up to 1Gbps of symmetric data transmission and it is perfectly suitable for FTTpd/FTTN applications.
NV-450M/S is a cost effective solution that delivers high-speed Internet access to end-users over existing copper wire infrastructure, not only NV-450M/S support future-proof super Vectoring (G.fast)compatibility,
NV-450S itself also support Vectoring(VDSL2) and super Vectoring(VDSL35b), and this solution is designed to meet the ISPs requirements to cover end users in different range of loop / areas .


 

 

• Compliant with IEEE 802.3 / 802.3u / 802.3ab Ethernet Standard
• Compliant with ITU-T G993.2 VDSL2 standard (NV-450S only)
• Compliant with ITU-T G998.4 G.INP standard (NV-450S only)
• Compliant with ITU-T G.9700/G.9701 G.fast standard
• Backward compatible VDSL2/V35b (NV-450S only)
• Support 106a/b & 210a/b dual G.fast band profile
• Support super Vectoring for V35b / G.fast(NV-450S only)
• Support Vectoring for VDSL2(NV-450S only)
• Support High Bandwidth up to 1Gbps
• Support USB 3.0 for connecting USB Dongle
• Support static routing for IPv4 and IPv6 forwarding(NV-450S only)
• Mac Address based filtering
• Support 8 queue MFC/DSCP both type QoS
• Support HTTP/HTTPS web management
• Support SSL security
• Support remote management and monitor
• Support configuration backup and restore
• On board surge protection for Line port
• Support bridge(switch) / Router mode(NV-450M bridge mode only)
• Support Dual Firmware Image Backup
• Support RJ-11 / Terminal block combo line port
• Support NTP Time Server.
• Support TR-069.
• On board POTS/ISDN splitter
• Support Jumbo frame(MTU) up to 1600 bytes
 
* Specifications are subject to change without prior notice.

TOP

 

 

 Standard Conformance
 Standard:

IEEE802.3/802.3u/802.3ab standards
ITU-T G9700/G9701 standards

ITU-T G993.2/G998.4 standards (NV-450S only)
  Regulatory Compliance:

 FCC
 CE 

 RoHS compliance
 
 Hardware Specifications
 Physical Interface:

4 x RJ-45 10/100/1000 Mbps Ethernet port
1 x RJ-11 / Terminal block combo for line port
1 x RJ-11 connector for POTS/ISDN phone device
1 x Reset Button for resetting to factory default

2 x USB3.0 for connecting USB dongle
 LED indication:
1 x Power LED
4 x Link/Active Status for Ethernet port
1 x Link LED for G.fast mode
1 x Link LED for xDSL mode (NV-450S only)1 x Master(CO)

LED(NV-450M only)
 Power Requirement:
Input Voltage: 12 VDC (Commerical-grade power adapter)
 Typical Power Consumption:

NV450M:

7.92W (Full load, without USB port)
17.92W(Full load, with 2 x USB port)
NV-450S:
8.16W(Full load, without USB port)
18.16W(Full load, with 2 x USB port)
 Operating Temperature:
0°C ~ 50°C (32°F ~ 122°F)
 Storage Temperature:
 -20°C ~70°C (-4°F ~ 158°F)
 Humidity:
10 to 90% (non-condensing)
 Net Weight:
approx. 0.4 kg
 Dimensions:
196 x 146 x 40 mm ( 7.72" x 5.75" x 1.57”)

 

* Specifications are subject to change without prior notice.

TOP

 

Connect the NV-450M(Master) and the NV-450S(Slave) to the Line
The objective for LAN extender is to pass high speed data over a twisted pair cable. In the setup, connect NV-450M(Master) to NV-450S (Slave) through phone wire(24~26 AWG) or line simulator or any other hardware representation of a cable network, with or without noise injection and crosstalk simulations.

 

Proper Installation: Train & Metro Stations、Boat and Submarine、Parking system、Weather station、

Amusement park、Farm、Jail & Oil Refinery、Telecom.

 

 

 

Release Date
File
Version
Download
Feb, 2020
  Datasheet
N/A
Feb, 2020
  User's manual
A6

 

 

 

1. POWER indicator does not light up (green) after power on.

 

Check the power plug by plugging in another that is functioning properly. Check the power cord with another device. Check the terminal block make sure to fasten the power cord. If these measures fail to resolve the problem, have the unit power supply replaced by a qualified distributor.

 

2. NV-450M/S both cannot handsharking after making a connection.

 

    1. 2.1 Verify that the switch and attached device are power on.
    2. 2.2 Be sure the cable is plugged into both the switch and corresponding device.
    3. 2.3 Verify that the proper cable type is used and its length does not exceed specified limits.
    4. 2.4 Check the modem on the attached device and cable connections for possible defects.
    5. 2.5 Make sure that the phone wire must be connecting NV-450S first, when powered on.
    6. 2.6 Replace the defective modem or cable if necessary.
2.7 Checking Phone wire length if exceed 600m(1968ft)

 

3. Line Link cannot be established.

 

  1. 3.1 Please make sure that the phone wire must be connected between NV-450M(Master) side and NV-450S(Slave) side when both are power on. NV-450M Master side will do link speed function depending on phone wire length, therefore if NV-450M Master side can’t detect Slave Side over phone wire while both power on, this will cause the Link to fail.
  2. 3.2 Please check phone wire, we recommend use 24-26 gauge with twisted pair and without rust.
  3. 3.3 Please reinsert power when change cable length or link time over 3 minutes.
3.4 If NV-450S connect to IP-DSLAM and link failure, please try to change band profile as 17a for getting long reach.
  1. .
4. I just bought a NV-450M/ NV-450S to replace my Quest DSL modem for my home. I was told any VDSL2 modem would replace and give me higher communication speeds. It doesn’t get me internet when hooked up. All lights come on but no Link light. Is this the complete wrong application for this unit?

 

Please note NV-450S is a Slave (CPE side), it must be connected to the NV-450M Master(CO side) or IP-DSLAM to get link.

 

5.We need to set up a default gateway on a NV-450M/ NV-450S pair which are in Bridge mode, as they want to manage the units from a different network.

 

When the application is used within the LAN, the switch(bridged) mode is not necessary to set up a gateway .However, if the application crosses various network segments (LAN to WAN(Line) or WAN(Line) to LAN), you must set up a gateway to connect different network segment.
Regarding how to configure a default gateway at switch(bridged) mode for crossing various network segments .
Configuration gateway example from Static Routing:
Destination LAN IP: 0.0.0.0
Subnet Mask: 0.0.0.0
Gateway:  192.168.16.1

Note: Static Routing functionality is used to define the connected Gateway between the LAN and WAN.

.

 

6. What can I do if I forgot my password.

 

If you forgot your password, you must reset your modem. Unfortunately this process will change all your settings back to the factory defaults. To reset the modem, locate the reset on the rear panel of the unit. With the modem powered on, use a paperclip to hold the button down for over 5 seconds. Release the button and the modem will go through its reboot process. NV-450M default ip is  192.168.16.249. NV-450S default ip is 192.168.16.254.When logging in, the default username and password both are “admin”.

 

7. What is the maximum Ethernet frame MTU for these modems?
  2. NV-450M / NV-450S jambo frame(MTU) up to 1600 bytes.